DT8032B
8 Channel 500 V/ 1 mA Desktop Power Supply Module (USB/Ethernet/Touchscreen)
Features
- 8 independent channels in a Desktop case (110/220V AC Powered)
- 500 V / 1 mA output range
- Channels with either positive or negative polarity
- SHV coaxial output connectors
- Low Ripple
- Under/over-voltage alert, overcurrent and max. voltage protection
- Interlock logic for board enable and Individual channel kill
- 5 nA Current monitor resolution (with x10 Imon-Zoom: 500 pA)
- Zero Current compensation
- 2.8″ color touch screen display
- Local and Remote control (USB2.0/Ethernet)
- Software Tools for easy channel management
Overview
The CAEN Mod. DT8032B provides 8 independent 500 V/ 1 mA channels in a Desktop package (110/220V AC Powered). Each channel can provide a 500V max voltage and a 1 mA max current. The unit is available with positive, negative and “mixed” (4 positive and 4 negative) channels. Channels outputs are delivered through SHV connectors. The HV output RAMP-UP and RAMP-DOWN rates may be selected independently for each channel in the range 1÷100 V/s in 1 V/s steps. The module features 5 nA Iset resolution.
|
SHV connector
HV coaxial connector, 8 channels for Mod. DT8032B |
Consult our connectors reference page for technical information.
Module control can take place either locally thanks to a 2.8″ Touchscreen Graphic color LCD display with a completely redesigned user interface or remotely, via USB 2.0 or Ethernet.
A complete set of Software Tools is available to control these units; the user can freely download low level libraries, LabVIEW driver and Graphical application software.
Safety features allows the module to perform as a current generator and includes:
| Overvoltage and Undervoltage warning | When the output voltage differs from the programmed value by more than 2% of set value (minimum 10V). |
| Overcurrent detection | When a channel attempts to exceed the programmed current limit, it signalled to be in “overcurrent” and enter in a TRIP status. The output voltage is varied to keep the current below the programmed limit for a programmable TRIP time, then the channel is switched off. If TRIP is set to “constant current mode”, the channel behaves like a current generator. |
| Hardware VMAX and IMAX | Maximum output voltage and maximum current value can be fixed, via front panel potentiometer, at the same common value for all the board channels. IMAX and VMAX values can be read out via software. |
| Safety Board Interlock | Common Interlock logic for channels enable/disable and individual inputs signal for channel Kill function. |
Technical Specifications
- Package
Desktop module housed in a 239x84x184 mm3 (WxHxD) Aluminium case
(110/220V AC Powered)
- Output channels
8 channels, SHV connector
Positive, Negative or Mixed (4-8 positive and 4-8 negative) Polarity; common ground
- Output Voltage
0÷500 V
- Max. Output Current
1 mA
- Max. Ch. Output Power
0.5 W
- Vset Resolution
2 mV
- Vmon Resolution
2 mV
- Iset Resolution
5 nA
- Imon Resolution
5 nA (high range) / 500 pA (low range)
- Vmax
0 ÷ 500 V
- Vmax resolution
1 V
- IMAX hardware
1 mA
- IMAX hardware resolution
1μA
- Ramp Up/Down
1÷100 Volt/s, 1 Volt/s step
- Trip
Max. time an “overcurrent” can last (seconds). A channel in “overcurrent” works as a current generator; output voltage varies in order to keep the output current lower than the programmed value. “Overcurrent” lasting more than set value (1 to 9999) causes the channel to “trip”. Output voltage will drop to zero either at the Ramp-down rate or at the fastest available rate, depending on Power Down setting; in both cases the channel is put in the off state. If trip= INFINITE, “overcurrent” lasts indefinitely. TRIP range: 0 ÷ 999.9s; 1000 s = Infinite.
Step = 0.1 s
- Voltage Ripple
10 – 1000Hz: <4mVpp typ; <6mVpp max
1kHz – 20MHz: <2mVpp typ; <4mVpp max
- Vmon vs. Vout Accuracy
± 0.02% ± 100mV
- Vset vs. Vout Accuracy
± 0.02% ± 100mV
- Imon vs. Iout Accuracy
± 0.5% ± 5µA
- Iset vs. Iout Accuracy
± 0.5% ± 5µA
- Humidity range
0 ÷ 80% non condensing
- Operating temperature
0 ÷ 45°C
- Storage temperature
-10 ÷ 70°C
- Vout / Temperature coefficient
±50 ppm/°C typ
- Long Term stability (1 week after 1h warmup)
±0.04% / full scale
- Local Control
LCD touchscreen
- Remote Control
USB & Ethernet
Compare
Compare with Desktop High Voltage Power Supplies.
Loading...
Ordering Options
| Code | Description |
|---|---|
| WDT8032XBAAA | DT8032BN - 8CH Desktop Programmable HV Power Supply (-500V 1mA) -SHV conn. - Common Gnd RoHS |
| WDT8032XMBAA | DT8032BM - 8CH Desktop Programmable HV Power Supply (4ch +500V 1mA, 4ch -500V 1mA) -SHV C. Gnd RoHS |
| WDT8032XPBAA | DT8032BP - 8CH Desktop Programmable HV Power Supply (+500V 1mA) - SHV conn. - Common Gnd RoHS |
Related Products
Related Software
LabVIEW Driver (PSM - Power Supply Modules)
LabVIEW Instrument Driver for Power Supply Modules
GECO2020
GEneral COntrol Software for CAEN HV Power Supplies
CAEN HV Wrapper Library
Library for CAEN Power Supply Control