EASY Subsystem Power Supply Module
Magnetic field and radiation tolerant
Six 12 kV / 1 mA channels
Channel floating up to 5 V between each other
VMax and IMax set by trimmer
Channel protections: overvoltage, overcurrent, overtemperature
On/Off for each channel
Interlock capability
Local and remote 48V Service on/off
Please note: the A3512 has been superseded by the A5512.
The CAEN Mod. A3512 is a 6 Channel 12 kV / 1 mA Power Supply Board, developed for operation in magnetic field and radioactive environment. Each A3512 houses six individual floating channels, floating up to 5 V between each other, each rated 12 kV / 1 mA. The board is available in a negative (A3512N) and a positive (A3512P) version, both also offered as low noise versions (A3512HN and A3512HP).
The output voltage can be set with 1 V monitor resolution, while the output current is monitored with 100 nA resolution. For each channel, a voltage protection limit, SVMAX, can be fixed via software with 1 V resolution, and the output voltage cannot be programmed beyond this value.
The outputs are available on a CPE HV connector, a High Voltage Single Pin type with 6 channels, used on both the Mod. A3512 and the Mod. A3512H. For further technical details, please refer to our connectors reference page.
Its safety features allow the module to perform as a current generator. All channels can be enabled or disabled through the Global Interlock logic. If the output voltage differs from the programmed value by more than 3% of the voltage full scale range, the channel is signalled to be in either Overvoltage or Undervoltage condition.
If a channel tries to draw a current larger than its programmed limit, it is signalled to be in Overcurrent condition and enters TRIP status: the SY1527 system detects this state as a fault and reacts according to the setting of the TRIP parameter. The output voltage is varied to keep the current below the programmed limit for a programmable TRIP time, after which the channel is switched off. If TRIP is set to “constant current mode”, the channel behaves like a current generator.
The board temperature can also be monitored, and the board status can be checked through the TEMPERR flag, which is raised above 65 °C: when the board is in TEMPERR status, all channels are switched off.
Finally, the Hardware VMAX and IMAX values, which set the maximum output voltage and the maximum current, can be fixed via a front panel potentiometer at the same common value for all the board channels, and can be read out via software.
|
Image
|
Name
|
No. of Channels
|
Connectors
|
No. max of boards per crate
|
Width (slots)
|
Max power per channel (W)
|
Iset/Imon resolution
|
Vset/Vmon resolution
|
Current Full Scale
|
Voltage Full Scale (V)
|
Max Ripple (mVpp)
|
|
|
A3501 |
12 |
SHV |
10 |
2 |
0.1 |
100 nA |
100mV |
1 mA |
100 |
30 |
|
|
A3535 |
32 |
SHV |
5 |
4 |
1.75 |
100 nA |
500 mV |
500 µA |
3200 |
30 |
|
|
A3512 |
6 |
CPE HV |
7 |
3 |
12 |
100 nA |
1 V |
1 mA |
12000 |
50 |
|
|
A3540 |
12 |
SHV |
10 |
2 |
4 |
100 nA |
500 mV |
1 mA |
4000 |
30 |
|
No. of Channels |
6 |
|
Polarity |
Positive (A3512P, A3512HP) or Negative (A3512N, A3512HN), with Floating return |
|
Output Voltage |
0 ÷ 12 kV (connector output) |
|
Max. Output Current |
1 mA |
|
Voltage Set/Monitor Resolution |
1 V |
|
Current Set/Monitor Resolution |
100 nA |
|
VMAX hardware |
0 ÷ 12 kV |
|
VMAX hardware accuracy |
± 2% of FSR |
|
VMAX software |
0 ÷ 12 kV |
|
VMAX software resolution |
1 V |
|
Voltage Ripple |
|
|
Voltage Monitor vs. Output Voltage Accuracy |
|
|
Voltage Set vs. Output Voltage Accuracy |
|
|
Current Monitor vs. Output Current Accuracy |
|
|
Current Set vs. Output Current Accuracy |
|
|
Weight |
3.5 kg |